 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Telefon: +49 (0)6135 931069 Telefax: +49 (0)6135 931070 www.peak-electronics.de info@peak-electronics.de PD10NG-XXXXE2:1 1KV ISOLATED 2W REGULATED SINGLE OUTPUT SIP8 Electrical Specifications (Typical at + 25 , nominal input voltage, rated output current unless otherwise specified) Input Specifions Voltage range Filter 4.5-9, 9-18, 18-36 and 36-72 VDC Wide lnput Capacitor type 1000 VDC 1 G 68 PF +/-2 %, typ. 100 mV p-p, max. Continuous, auto restart +/-0.2 % typ. +/-0.5 % typ. load = 10 ~ 100% +/-0.02 % / Refer to the table 75 KHz, typ. - 40 to + 80 - 55 to + 125 Up to 90 %, non condensing Free air convection 21.80 x 9.20 x 11.10 mm Non conductive black plastic lsolation Specifications Rated voltage Resistance Capacitance Output Specifications Voltage accuracy Ripple and noise (at 20 MHz BW) Short circuit protection Line voltage regulation Load voltage regulation Temperature coefficient General Specifications Efficiency Switching frequency Environmental Specifications Operating temperature (ambient) Storage temperature Humidity Cooling Physical Characteristics Dimensions SIP Case material Samples of Partnumbers PART NO. INPUT VOLTAGE (VDC) INPUT CURRENT NO LOAD (mA) INPUT CURRENT FULL LOAD (mA) OUTPUT VOLTAGE (VDC) OUTPUT CURRENT (max.mA) EFFICIENCY FULL LOAD (% TYP.) PD10NG-053R3E2:1 PD10NG-0505E2:1 PD10NG-0509E2:1 PD10NG-0512E2:1 PD10NG-0515E2:1 PD10NG-0524E2:1 PD10NG-123R3E2:1 PD10NG-1205E2:1 PD10NG-1209E2:1 PD10NG-1212E2:1 PD10NG-1215E2:1 PD10NG-1224E2:1 PD10NG-243R3E2:1 PD10NG-2405E2:1 PD10NG-2409E2:1 PD10NG-2412E2:1 PD10NG-2415E2:1 PD10NG-2424E2:1 PD10NG-483R3E2:1 PD10NG-4805E2:1 PD10NG-4809E2:1 PD10NG-4812E2:1 PD10NG-4815E2:1 PD10NG-4824E2:1 4.5 - 9 4.5 - 9 4.5 - 9 4.5 - 9 4.5 - 9 4.5 - 9 9 - 18 9 - 18 9 - 18 9 - 18 9 - 18 9 - 18 18 - 36 18 - 36 18 - 36 18 - 36 18 - 36 18 - 36 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 36 - 72 41 37 38 37 37 37 24 23 22 22 22 22 12 12 12 12 11 11 8 7 7 7 7 7 487 455 458 452 452 452 237 219 215 212 212 217 117 111 108 105 102 106 58 54 53 52 52 53 3,3 5 9 12 15 24 3,3 5 9 12 15 24 3,3 5 9 12 15 24 3,3 5 9 12 15 24 606 400 222 167 133 83 606 400 222 167 133 83 606 400 222 167 133 83 606 400 222 167 133 83 68 72 71 73 73 73 70 75 77 78 78 76 71 74 78 79 80 78 72 77 78 80 80 78 PD10NG-XXXXE2:1 1KV ISOLATED 2W REGULATED SINGLE OUTPUT SIP8 Dimensions PEAK Modelcode 21,8 9,2 1 23 5 678 11,10 0.50 0.05 3.10 typ. 0.50 0.05 2.54 typ. 0.25 0.05 3.20 typ. 2.0 0.50 Recommended footprint details 2,54 XX.X 0.5m/m XX.XX 0.25m/m Unit : mm 1.00.15 /0 2,54 Derating Graph and Pinning Output Temperature Derating Graph Ambient Temperature C Pin # 1 2 Connection Single - + V V Input Input Ctrl Omitted NE + - V V Output Output CS 2.00W 3 4 5 Safe Operating Area 6 7 8 40 0 40 80 100 Control input can be left open (3) No external connection allowed (5) Optional external capacitor (8) PD10NG-XXXXE2:1 1KV ISOLATED 2W REGULATED SINGLE OUTPUT SIP8 External capacitance: These converters will work with without external capacitors but they are necessary in order to guarantee the full line load range. All parts have been tested using the following recommended values. + Vin Pin 3 (CTRL) Control pin (ON/OFF) Output starts at low or open and stops when high. Voltage applied via a limiting resistor and switching diode. The converter is in a low power mode during the high level phase. + Vout Cin - Vin Cin Cout Converter Connection example Cout - Vout 10uF/100V, low ESR. 100uF/35V, low ESR. MCU Vcc-5V 1K 1N4148 CONVERTER PIN 3 Pin 8 (CS) This pin provides a connection point to the main reservoir capacitor. Additional capacitance can be added from this to pin 7. Any low ESR capacitor will improve ripple and noise in some measure. Starting values can be in the range of 100uF. Pin 5 (NE) This pin is used internally and must have have no external connection. Application Notes Pin 3: The outside control connection. This pin provides the converter output ON/OFF, and the control common is referred to negative input. Pin 5: This pin belongs to the secondary side. It just avoids someone to reverses the primary and secondary. Pin 8: Max. 1000 uF Specification can be changed without notice. Copyright PEAK electronics GmbH REV: 1 / 03.2003 |
Price & Availability of PD10NG-483R3E21
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |